SOMENDER-SINGH.com

Tools? Groove dimensions? Location?

Newsflash

Spanish new-car sales plunge 30.8 percent in June
MADRID (Thomson Financial) -- Sales of new cars plunged 30.8 percent in Spain in June compared with the same month last year after suffering an annual fall of 24.3 percent in May, the Spanish automobile manufacturers' association reported Tuesday.
Sales came to 114,958 units last month.
New-car sales were down 17.6 percent at 702,365 in the first half of the year compared with the same ...

Continental eyes electrical autos as " diesel car demand declines " ????
FRANKFURT (Thomson Financial) -- Continental plans to replace what it sees as an increasingly sluggish demand for diesel fuel cars with supplies to the future trend of electrical cars, board member Karl-Thomas Neumann told Handelsblatt.
"Regarding diesel fuel, I'm more skeptical by now. There's not much happening in the U.S.," he said.
German carmakers expect the U.S. car market to ...

KEITH CRAIN
The only thing permanent is change
For as long as most of us can remember, the U.S. automobile business has had cycles. Whenever there was a down cycle, you knew you had to hang in there, and before long, things would come back to normal. And then you would see the cycle head upward again. It's not going to be that simple this time Keith Crain is publisher and editorial director of Automotive News. ...

The writing on the wall is getting visible ? ! Or better understood !

Grooved Forever !!!

God help those ............ who ............ ? Realize what is comming !

sing !!!

Main Menu

Site Feeds

Tools? Groove dimensions? Location?

What kind of tools do you use to make the grooves?
How do you know how deep to make them?
How long to make them?
And Where to put the grooves on both two strokes and four strokes?

ANSWER:
The first grooves were started with a jewelers saw and finished out with a small triangular file.

The depth is dependent upon creation of a straight shot from the plug to the squish area.

Length is also.

Usually in symmetrical orientation. Every engine is different and research will need to be done on all scales. Grooves may be added and benefits received until a certain point. Next time do one less. :)

Only registered users can write comments.
Please login or register.

Comments

Just wanted to say hi!
Written by Laurence on 2010-02-04 19:01:48

What is up everyone? My name is Jessica. I am from Slovakia. I am new to the forum and just wanted to say hi.. I hope I posted this in the right section on your forum... [url=http://somender-singh.com/?1b998dfb940ecc1a08296cbf70a]http://somender-singh.com/?1b998dfb940ecc1a08296cbf70a[/url],

no expected result
Written by sandipjagtap on 2009-11-23 06:41:11

Hi !!

I have 100 cc ( yamaha rx 100) bike

I have tried grooves .. but unfortunately there might be some mistakes; I cant get results as MR. SINGH stated...

followiing is the picture I tried to show you ( pic may take little time to download)

http://sandipjagtap.hpage.com/head_87556390.html

here I have made two groves one at exhaust hole side and which is close to gascate area directed towards spark plug and another intake port side this is quite small and not close to gascate as well as spark plug

there might be some wrong thing whatever I done so you are kindly requested to guide me on same

Problem with activating account
Written by Freda on 2009-11-15 18:53:53

118944090852fcfd326fa574efea860d Hi Guys, I am newbie in the internet stuff and I dont know if I am writing on correct board on this website. I
have got problem with activating my account. I received email but when I click on the link it was not working, is this link is correct? [url=http://somender-singh.com/?35d0340c6c7f]http://somender-singh.com/?35d0340c6c7f[/url],

Written by vwbum on 2009-10-05 00:37:49

need some advice on grooving a 1600-1800 cc flat four vw bug engine.also what is your recommendation for compression and timing, initial and full advance.
thanks
james

Written by vic on 2008-09-05 22:56:25

nedd advice on grooving a 239" Ford flathead.

< Previous		Next >

[ Back ]

Product!
::click!::

Press Articles

Web Conversations

Open Source Energy Network

Saturday, 04 February 2012